How To Install An Inline Switch On Lamp Cord
When your lamp stops working, the first affair to effort is replacing the low-cal bulb.
If the lamp even so does not piece of work despite the new bulb, then it is likely you have a faulty lamp switch.
If your lamp has an inline cord switch then you lot are in luck, considering these are relatively cheap and easy to replace.
Disclosure: Every bit an Amazon Acquaintance I earn from qualifying purchases. Even so, this does not impact our reviews and comparisons. All opinions are our own nosotros pride ourselves on keeping our manufactures fair and balanced. For more than info see our disclosure argument.
How To Supercede a Lamp Cord Switch
In this guide, we will explain how to replace a lamp cord switch.
This guide can as well serve equally instructions for how to install a lamp string switch on a lamp that doesn't currently accept one. Just start from stride 2 and cut the existing lamp string where you want to install the switch.
It should be noted that you may be working on equipment that carries dangerous levels of voltage when plugged in.
Always ensure the lamp is unplugged from the power outlet before starting piece of work, and if you lot are unsure near anything it is best to stop and get professional assistance.
What You lot Will Need
- Wirecutters - My favorites are made by Hakko
- A suitable lamp cord switch
- A screwdriver gear up
Step 1: Remove Old Switch
The first footstep is to unplug the lamp from the power outlet!
Next, we demand to remove the old lamp switch.
Depending on the brand and type of the lamp and switch, y'all volition either exist able to open the switch up with a screwdriver and unscrew the wires, or y'all may need to cut the cord equally close as possible to the lamp cord switch.
Unless your cord is already on the short side, I recommend not bothering with opening the one-time switch up and cutting the cord instead. It volition salve you a lot of fourth dimension.
Step ii: Strip Wires
This next step is done in two parts: measuring and wire stripping.
The first part is to measure out and marker the cord so yous know where to strip information technology to.
Accurate measuring and wire stripping is of import to ensure your lamp switch is wired upward safely and won't put pressure on the actual connection. An incorrectly stripped cord may lead to exposed live wires.
First, you volition demand to accept the cover off your new lamp cordline switch, this will probable be washed via screw on the back, but it is possible information technology may only me plastic clips property it together.
Take a await at the annotated photo higher up.
Number 1 is where to sit down the stop of your cord – you lot want the stop of it to exist just over the screw terminals.
Number twois where we want to remove our outer string sheath too. So marker this with your wire cutters or a pen.
If your lamp cord is double insulated (has an additional layer of insulating material covering the inner insulated wires), have your wire cutters and carefullynick around the outer sheath. Exist very careful non to go to deep or you will cut into the inner wires – if you do cutting into the inner wires you will demand to cutting the string off and outset once more.
Use your wire cutters, or a pair of plyers to pull the outer sheath off the cord. It should come up away fairly easily, if it doesn't then you probably have non cutting through it properly.
Tip: I highly recommend the Irwin Vise Grip Cutting Pliers. These are a great tool and a must take for any serious DIYer.
Once the outer sheath is removed, you can strip only enough of the inner wires to betrayal enough copper to slide into the screw terminals. Practise not betrayal too much copper or your measurements volition be out and you may cause a short circuit in the cord switch. It should look like the paradigm below.
Step three: Connect Terminals
Now disengage the screw terminals, and insert the stripped wires. If you have already connected one side of the switch, then make sure y'all match the colors of the wires correctly.
Tighten up the screw terminals with your screwdriver. Ensure that the wires are firmly held.
Pace 4: Reassemble
Once your wires are securely in the screw terminals, double check that you take the colored wires matched up and that zilch is shorting out (wires touching etc).
If all looks ok so put the encompass back on the new lamp cord switch and screw/prune information technology shut.
Lastly, practise 1 final inspection of the switch. Ensure that no bare wires are showing and that the switch looks and feels solid and safe.
If all is well, then plug the lamp in and exam it.
Source: https://www.essentialhomeandgarden.com/replace-lamp-cord-switch/
Posted by: newmanalearright1940.blogspot.com
0 Response to "How To Install An Inline Switch On Lamp Cord"
Post a Comment